04 ECSB Silverado Build Bagged..

[12VoLt Shocker]

Ill get started with the full back story....

I bought the truck with 18k miles, sitting on the side of a garage with the windows down, layed out, and there it sat for at least 4 years...
I paid 800 cash, and traded a stereo system that we installed at work and I payed my boss back the balance @ cost of goods...
So all totaled I have about $1,800 into the original purchase of the truck...
This is what it was.....
http://c4.ac-images.myspacecdn.com/images02/33/l_34a1f696e555492c93fea1f0799ddf1f.jpg
http://c2.ac-images.myspacecdn.com/images02/39/l_a692e52482ad40859753eb5218b23e01.jpg
yep makes you cringe right...well thats not the worst of it...
did I say the windows were down....
http://c2.ac-images.myspacecdn.com/images02/34/l_514f417527f74b099886cb72631f3349.jpg
It was closer to a trash can than a truck...
http://c1.ac-images.myspacecdn.com/images02/13/l_9587c78c51cd40b698db240ae91a8aec.jpg


So the first list on things to do was get it off the trailer and clean it up.. Just to see whats there....what needs to be fixed and what else I might find...:mrgreen:

bed cleared out just hinting at what is there....
A solid 2 link with bag behind bar and some wild ass panhard...
http://c3.ac-images.myspacecdn.com/images02/58/l_359969ae4aff43dcb25293628375cdbe.jpg
you can see the dirt on the interior just built up over the years..
http://c4.ac-images.myspacecdn.com/images02/6/l_425fcebfa7764ff6879b79300d47eda3.jpg
I also sent some power pulsing through it... I really wanted the windows up and just needed to see why they didnt roll them up in the first place...
It just needed a battery .. thats it...:eek:
the original miles....
http://c2.ac-images.myspacecdn.com/images02/7/l_5c00b1e681a144fb873e69ac3577b09d.jpg
And cleaned the interior all the way...
http://c4.ac-images.myspacecdn.com/images02/59/l_06f71d4ad7dd4948a59500322154cbb3.jpg
Rats nest alarm and deck relocation I found under the dash...
http://c1.ac-images.myspacecdn.com/images02/10/l_d178006438a343d8b62e21a417604f04.jpg

Later I cleaned out the bed, removed the tank, extended bedrails, old tailgate and painted all the rusty stuff just to cover it....I also picked up a new tailgate, front bumper lower piece, both of them were free...f
http://c1.ac-images.myspacecdn.com/images02/1/l_e8c9984bd3f54a8d9827d12c57fd879c.jpg

And the MONEY shot...!
http://c1.ac-images.myspacecdn.com/images02/32/l_3b2dd28f03b340a8800d4563408851a8.jpgTuckin 22's
At the time I just borrowed that wheel just to see fit and clearance

[12VoLt Shocker]

Moved it to a buddies house and took the bed off to see the frame and start fixing/changing it to what I would want....

http://c3.ac-images.myspacecdn.com/images02/57/l_0824fe41d37f4f27a24b3d84ea82ae5a.jpg
http://c3.ac-images.myspacecdn.com/images02/53/l_36092b7afe0843918014b1fa1ad92066.jpg
OMG this truck was bitch banged or just done by a few idiots...
The drivers side frame rail is bent inward 2 inches at the very back...
so no where near square...Everything was stupid IMO.....

So what did I do... Cut that **** off and do it my way...
http://c3.ac-images.myspacecdn.com/images02/92/l_cf87e49fd20c4ad088bebd63d168965e.jpg

This is the tank in the stock location and clearing frame by 2 inches...
No Problems laying out on stock tank...
http://c1.ac-images.myspacecdn.com/images02/81/l_a31e5151d0ab4779af2944f84266bb40.jpg
AND I STARTED IT FOR THE FIRST TIME...... NO CHECK ENGINE LIGHTS!
RUNS LIKE A BRAND NEW TRUCK!
Its Alive.... First time It MOVES under its own power... Video by 12 Volt Shocker - MySpace Video (http://vids.myspace.com/index.cfm?fuseaction=vids.individual&videoid=57195143)

Ohh yea I also bought those 22's, A set of 4 wheels and tires PLUS! 3 spare rims......for $1600....My baby looks good in some new shoes....
http://c4.ac-images.myspacecdn.com/images02/19/l_86f842dd1c974db08f55b4e84bb12817.jpg
And Picked up a better bed than my warped ass one...
http://c3.ac-images.myspacecdn.com/images02/103/l_29fd2537f5fa4d6aa98dc6f3781d5bd2.jpg

[12VoLt Shocker]

Moved the truck back to my house... IT was way out in the boonies and hated not having it to work on...Plus it got hail damage sitting in the damn yard...
http://c1.ac-images.myspacecdn.com/images02/78/l_771627effffa49a08fe6141391454f20.jpg

Bought some other goodies ....

A SuicideDoor wishbone kit.... bag cups for the front...2x3 gallon tanks...
http://c1.ac-images.myspacecdn.com/images01/104/l_ea1f0a9d8c36cb0a0e80e695aa1073b4.jpg
AND the #1 best toy to date... :rolleyes: my fav toy ever...
http://c2.ac-images.myspacecdn.com/images02/105/l_de151f9f2e0846db996e711a8eb557cd.jpg
Its a must since I want to do this build my way got to have MY tools...:mrgreen:
My first weld with it...
http://c2.ac-images.myspacecdn.com/images02/68/l_e0c6cdf6d4ce40aab6fb316539177c65.jpg


I am going to skip a head to whats current ... you just missing a few steps to get where it is now but the change is easy to pick out...;)

NEW 07 hood since my hood was all Fked up from the golf ball hail....FREE also.
http://c1.ac-images.myspacecdn.com/images02/80/l_6c1e9a2777d546fbb48ae66841e52080.jpg
http://c1.ac-images.myspacecdn.com/images02/80/l_acaa875de55241999d90346fc0cde630.jpg

DC 9000 Comp, 0psi to 100psi in 55 sec on a 5 gal tank...
http://c2.ac-images.myspacecdn.com/images02/109/l_0dcaf1f89e6e47feb5429271f55a6b45.jpg


Picked up a new rear end out of a 07, Mine was bent from the other guy welding on it....All of it was only $220 Including the lawn Mower...
http://c3.ac-images.myspacecdn.com/images02/77/l_25bb46206c004f929679ef9e8651f93e.jpg

[12VoLt Shocker]

And Now with my Full custom back half...

12 piece Bridge and bag mounts...
( need to update with the new bag mounts installed.)
Dual adjustable tank mounts, Gussets on the notch, and a battery area across from the gas tank area...Still doing moor to this... but that is the latest...
http://c3.ac-images.myspacecdn.com/images02/105/l_29439d7e2f05404a9e1cff848e645efa.jpg
http://c3.ac-images.myspacecdn.com/images02/65/l_95b69106a2274cfc824bceea3c7de11e.jpg
http://c4.ac-images.myspacecdn.com/images02/111/l_305397e962454c6ea474bd793245d4ff.jpg

Ohh and thow in another FREEBIE! I Had a customer want to toss his back seat for a system... .Lucky for him We have a huge dumpster... I took care of that for him... Now I dont need to pay for it... :mrgreen:
http://c4.ac-images.myspacecdn.com/images02/49/l_736e412621f244a4bff855a67c3ce803.jpg


Did I say that this was My first build on any type of bagged anything, even my first time welding....:

[12VoLt Shocker]

I did get some work done lately.... I finished seting up the rear end and I have the 3rd member mocked up and tacked...
http://c2.ac-images.myspacecdn.com/images02/64/l_1bf7cbafbe574036807b6ae195783e4d.jpg
http://c4.ac-images.myspacecdn.com/images02/52/l_d15c22a5b03a48d09b98cd3bcc288923.jpg

This is just a Moched up and tacked 3rd member, It will be beefed up quite a bit...

My alxe at full lift keeps the same pinion angle(-5 degrees) as it does layed all the way out, and only shifts 1/2 a inch backwards.

[12VoLt Shocker]

Well I started on my shock mounts... This is what I got so far...
http://c3.ac-images.myspacecdn.com/images02/20/l_8aec289acbe547d0a2e0ffe41688238e.jpg
http://c4.ac-images.myspacecdn.com/images02/53/l_f973b676836c4a289e48e0bac77de847.jpg



And I mounted My bag brackets *tacked* into place...
http://c4.ac-images.myspacecdn.com/images02/56/l_fdd7bd73d16547d5891ff41d6dbe7e1f.jpg
http://c4.ac-images.myspacecdn.com/images02/111/l_16a186dccd944e209cd2d160d15f7423.jpg
All Up....




All Down....
http://c1.ac-images.myspacecdn.com/images02/33/l_18f7e69a60cf4b4193694667a26ba820.jpg
http://c4.ac-images.myspacecdn.com/images02/31/l_381c3ea447d9423599d92af03915ca5f.jpg
Now I just need to pull the rear end and weld it up.:

[12VoLt Shocker]

PSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSST....

Its DONE..... well ok its not all done but mostly all the fabrication is done in the rear area... Minus the shocks witch I have no clue where to go with them...:whatever:
NE who as promised..... A little VIDEO..!:fjoe:

Drop and Destroy Video by 12 Volt Shocker - MySpace Video (http://vids.myspace.com/index.cfm?fuseaction=vids.individual&videoid=63722597)


And Trying out the Wishbone hittin some sides...
http://c1.ac-images.myspacecdn.com/images02/34/l_87208de880994ce48c9ae417e47e302c.jpg
http://c4.ac-images.myspacecdn.com/images02/46/l_58f873a6f55d44eba74eb79188185de3.jpg

I also gusseted the 2 link tabs on the axle for extra insurance..
I had 6 gussets left over so I put them to work...:biggrin:
http://c2.ac-images.myspacecdn.com/images02/36/l_dd2a65171a1744f380af2584a10e2899.jpg

[12VoLt Shocker]

So am I going to keep posting on my build log and nobody is even looking?:huh:
ahh well...
.Yep that was my Shock tab...
This is what I came up with...
All these parts except for the shock mount tabs themselves are leftover pieces from the original bag behind axle kit..
I had no real use for them so I figured out a way to,
I cant waste good laser cut steel and DOT tubing :nono:
http://c1.ac-images.myspacecdn.com/images02/47/l_860ddd3273694231a662de8f4f5a6c44.jpg
http://c3.ac-images.myspacecdn.com/images02/80/l_f6a33949450c4eab83eeb34aea706f92.jpg
http://c4.ac-images.myspacecdn.com/images02/48/l_25970946af1e41d7ac25252fdda1f277.jpg
http://c4.ac-images.myspacecdn.com/images02/20/l_2ac524a6171643f0898d57ac4cd91aaf.jpg
And look how much better my welding has become..
http://c2.ac-images.myspacecdn.com/images02/89/l_41cd87c09f6547de8d49e43766356c79.jpg
http://c4.ac-images.myspacecdn.com/images02/4/l_54c1d54c890341b3882fcecdf78466df.jpg

Well thats about it for tonight.

[12VoLt Shocker]

I Did it.. I think I am done with the rear section !!
Unless I can find anything else to do on it... DONE!
All Down...
http://c3.ac-images.myspacecdn.com/images02/25/l_18a3a1271a634305b5c77c8462b4f55e.jpg
All Up...
http://c1.ac-images.myspacecdn.com/images02/37/l_a0798fd3ef074c6d82c8a9df9c62093c.jpg
http://c4.ac-images.myspacecdn.com/images02/55/l_4df3853050754c9aa67af35c8304507b.jpg
http://c3.ac-images.myspacecdn.com/images02/47/l_a5f3a1da477747e593f244a98f69b4e2.jpg

[flamethrower85]

looking good man, and the wheels look good on this thing, keep up the progress man

[12VoLt Shocker]

Thx for the good word...

I am making some progress lately, It has been hard because We just had our 2nd kid on the 8th of Oct and that has eating up all our time literally...:lol:

BUT I did have some time to
Get all OCD on beefing up the frame....
Stripped it down and NOW I am ready for paint...

I plated the notch on top bottom and to the factory frame...
It overlaps all the but welds under it...
http://c3.ac-images.myspacecdn.com/images02/2/l_4acee75097824e2f929823cbd301caee.jpg
http://c3.ac-images.myspacecdn.com/images02/43/l_ecdc24f193994ad9a12777d00c3fbfbe.jpg
It was 3x1/8 Flat stock and 2x1/8 flat stock....

I checked into what it will take to FIX the exhaust...
I found that the MORON had cut all the sensors off instead of just unpluging them...
So Now I need 4 new sensors * I can tune out 2* and a custom exhaust.

[12VoLt Shocker]

Well I got a few things done in the last couple of days...
I am just gonna copy paste from my FSC.com build log...kk
Well .............................................

















I got a couple of NEW feebies....
A Treo Amp for my mids...
And A Python SST 2 way Remote start...

I won both In Training for my Job..
Both Retail for $500
I answered a TRICK question to win the amp,
and I Won the Alarm Because My # was drawn...
I got some sick luck lately...:lol:
http://c2.ac-images.myspacecdn.com/images02/43/l_dc52f4d9329048daac52c8f419cb82a9.jpg



I also Went out and bought myself a Paint gun, Some tractor pant *Van Sickle* and went to town... This is a First for me also I have never painted from a gun... Only from a Can... :wink:



http://c1.ac-images.myspacecdn.com/images02/91/l_4af7d8eed90942c9b3187d75dc6ab7e4.jpg
http://c4.ac-images.myspacecdn.com/images02/37/l_8559b67b76164a4797ad52f5e1e7cc17.jpg
http://c1.ac-images.myspacecdn.com/images02/94/l_ee784a0acb3e40cca31d10b0253fd48c.jpg
http://c3.ac-images.myspacecdn.com/images02/101/l_b5a0b897db514982bbf85b6194124796.jpg
http://c3.ac-images.myspacecdn.com/images02/58/l_e1e8401841b4413288c10791a43f45d6.jpg


Tell me what you think....:

I got it moving under its own power and air now!!!!:burn:

I am going to run around with the link bars and rear end un painted for a bit just to make sure they dont crack or anything paint might hide..

http://c4.ac-images.myspacecdn.com/images02/29/l_823d982e32024c8c8a596065759fbbf7.jpg
At 90 PSI
http://c4.ac-images.myspacecdn.com/images02/99/l_74ba2f04c81c44bda94fb191ea820d47.jpg

didnt have time to wash it ... but i wanted to post something..
http://c4.ac-images.myspacecdn.com/images02/44/l_5a816331335f4060a1e096f16d65ab0f.jpg
http://c2.ac-images.myspacecdn.com/images02/64/l_b6045236cee9488194cc70835063ac29.jpg
My relay for my compressor, Stinger 60amp, and my kinetik batt
http://c3.ac-images.myspacecdn.com/images02/33/l_f85491d163b34ffba14bdc103470f852.jpg
The Camber will be fixed when I do the front.... Its still not all that terrible though..
http://c4.ac-images.myspacecdn.com/images02/19/l_7d8ed268e8a842d59a9af000339b1c43.jpg

[12VoLt Shocker]

Ok I did some final fab work in the rear by making my Air compressor mount....

I used a Old army Loudspeaker cabinet, Removed the speaker and mounted a plate to the bottom of it...Then welded 2xpieces of 1x1 square stock to a 3 wide plate steel that bolts to the bottom of the box, that all slips into the 2x2 pieces coming up from the frame...

When its all done and the bed is on I will cut down the 1x1, and it will pierce though the bed and into the 2x2 and flush the box to the bottom of the bed...Should make a nice solid mount and easy to remove if needed....This way I wont even need get under the truck if I need to remove my compressor...
http://c1.ac-images.myspacecdn.com/images02/19/l_2b55102d833d49099924c6830b50f7c0.jpg
http://c1.ac-images.myspacecdn.com/images02/72/l_2c7c7ba52f6d44589628aac1c592d548.jpg
http://c1.ac-images.myspacecdn.com/images02/12/l_768577b9c2b740469b25901a2ad0c26c.jpg
The Coolest thing about the box is its well ventilated and the top comes off, for easy service, and I will Dynomat the whole box so you can't even hear my compressor....
http://c1.ac-images.myspacecdn.com/images02/75/l_9c48e43afebe40329d0496c78d5e4c3c.jpg

You would have loved the speaker... It actually was a JENSON!

[12VoLt Shocker]

Here it is... A CUSTOM 7 switch box... Made from Switches I Got from Suicide door for a $1 Each and a Old VW hubcap I had... Got All the wire, and connectors from work for free.....

So Its a $7 dollar switch box... :cool:

Sure its a little off the wall but it will fit my custom console when I build it and it also goes with the look I am shooting for.. * I need to find a "DOG DISH" chevy hub cap and swap it to that, But this works for now*

http://c3.ac-images.myspacecdn.com/images02/81/l_a8b9885f44c943b1816ea2c7312ae6fe.jpg
http://c1.ac-images.myspacecdn.com/images02/110/l_23ffee1a617941b1962b586d3c268724.jpg
It took me 3 times to figure it all out.. but it was simple in the end...

[1lo88zu]

Looking good 12volt.

[d21cruisa]

looks great man!

[00s10]

Damn dude u got a hell of a deal wish i could find a deal like that... You are doing a great job though hope to see it at a show soon

[12VoLt Shocker]

lol this truck was on Craigslist for about a year...

Yea Ive got nothing but luck, some bad on this build for the most parts its all been good...He royally fucked it up though...

[Doinitvanstyle]

looks sweet man!!

[TRUK-WERKS]

okay now you've posted all the progress Marcus so you better bring it to Okie Freeze-off no excuses do a promo for the store

[Brill]

I'm Jealous...

[1lowzu]

looks good

[okcderek]

...now its time to channel the cab.

[laid 1500]

bad ass ride bro. keep the pics coming.

[12VoLt Shocker]

okay now you've posted all the progress Marcus so you better bring it to Okie Freeze-off no excuses do a promo for the store

Help me get this truck to the Exhaust shop and Ill be driving it by the end of the week!!!

Thanks for the good word folks...


I Did manage to finish pluming all the air line... ect valves ect... And I wired up my Pressure switch...

I was going to roll it out side and cycle though all the switches and take some vid for ya.........But my day ended with me driving to Autozone to drop off BOTH my batteries for the truck cause the were dead as shit......
http://c1.ac-images.myspacecdn.com/images02/81/l_411594f395924e47b5d41de15067544c.jpg
Also wrapped up all my front valves setup today..
http://c1.ac-images.myspacecdn.com/images02/11/l_4a8267fcfe374d928651dad566bce30c.jpg
shouldnt have any problems with them freezing up there... LOL....
I still need to clean up some of the wiring but meh... Its done.. You know I never did Check behind that sill to see what is in there before I Mounted those with self tapping screws...Meh...Ill fix it if its done any damage...
Ohh and I went out and bought me something nice ...

http://c1.ac-images.myspacecdn.com/images02/4/l_4014d54a548d4989bda44b942cade848.jpg
Fancy Hardware! :P

[pjc970207]

like to see this truck in prson. looking good bro

[LONCOME]

lookin good man ! deff comin a long way from when you picked it up !

[12VoLt Shocker]

like to see this truck in prson. looking good bro

Bring a trailer and help me haul it to the exhaust shop and Ill clean the drool of it for ya...:rolleyes:

[low psi]

lookin good man ! deff comin a long way from when you picked it up !


Definitely......LOL!! Me and this dude pretty much started out in the same boat!!!!!

[12VoLt Shocker]

Definitely......LOL!! Me and this dude pretty much started out in the same boat!!!!!

So what are you building?

[Flatiron Fab]

So what are you building?

ask him what he traded for his current truck!

[low psi]

So what are you building?


An 04 full size...you've seen in on FSC......


ask him what he traded for his current truck!

HAHAHA.....LOL!!!!!.......A 1993 S-10

[12VoLt Shocker]

Tan hood, but the reverse of what I had NOW you have a 04 hood and had a 07 ...;) I rememberz now..

[AlwaysStunting]

i like it looks good keep up the work

[nopinch]

An 04 full size...you've seen in on FSC......

i dont mean to thread jack here but FSC blows compared to GMFS

[Xplowdr]

Marcus loves the cock......That is all

[85c10on20s]

ive followed the build of this truck since i saw it posted up on myspace..glad you finally made it on here.

[12VoLt Shocker]

well I didnt get the truck to the Exhaust shop today as planned but I did get the New RE8 bags installed and DROVE it for the first time...

It Rides nice enough with just bags ATM but still need to REDO the whole front setup and put the shocks in back....

I took it to the park for some PLAY time too....
http://c2.ac-images.myspacecdn.com/images02/33/l_06c248fc025a4dcaa12b6ebf2e0f9675.jpg
http://c4.ac-images.myspacecdn.com/images02/59/l_cc4846c54e5648d480bda26afad10247.jpg
http://c4.ac-images.myspacecdn.com/images02/39/l_7c959a95e043434191c4ffc88f924a97.jpg
http://c2.ac-images.myspacecdn.com/images02/46/l_17aa879a2fc542a19e2fa32e6a81d331.jpg


That was yesterday... BUT this morning I DID make it to the exhaust shop....
Pics to come later when I go wash it...

[12VoLt Shocker]

So you guys have missed my thread or just dont care about cool trucks....:lolsign::whore:

NE way once you get caught up on the LAST post... This is what is going down now...


Exhaust is DONE! Check....

http://c3.ac-images.myspacecdn.com/images02/53/l_e7e21b6e3ba54cf3b55c378f1ba15cba.jpg
Almost killed by a Deadly spider......Check
http://c4.ac-images.myspacecdn.com/images02/24/l_e1d3d042adc045e499a5b7cbc65e23d3.jpg
Add some Spider Killer.....Check...
http://c1.ac-images.myspacecdn.com/images02/48/l_6aa8bcf4362d4ac6b03c8e9eaf576694.jpg

Then I threw the bed on in about 14min....





And 7hours...:rock: Check...
http://c4.ac-images.myspacecdn.com/images02/99/l_697f8fa2d43a4ba2869c7cf926f37eff.jpg
http://c4.ac-images.myspacecdn.com/images02/73/l_97a8dd3fdc904297bd64c5fcc7140807.jpg
http://c3.ac-images.myspacecdn.com/images02/1/l_d1188893f73c408685707c81e2fedf4e.jpg
http://c1.ac-images.myspacecdn.com/images02/44/l_caad5b54c6cb4f4b9a041c60e747f258.jpg

[00s10]

Hell ya man i checked your progess on myspace u have alot of pics of this thing on there lol... I love the truck and espcially the wheels man cant wait to see more

[d21cruisa]

nice truck man!!!

[teckn9ne]

damn coming together nicely

[03on22s]

Nice!

[stantheman]

CRAP, CRAP and more CRAP!!!!........J/K Marcus, Really looks good man. Glad to see its moving on its own power now! Im not bagging the s/w anymore. Found me something else to play with. Pics as soon as its sitting in my driveway. :woot:

[91tyler1]

Looks fuckin good man

[Symonds94]

You have deff turned the truck into something nice, soooooooo when u planning on bd it lol jk it looks really good though

[laid 1500]

nice ride bro.

[low_life96]

more pics!!!!!

[BIGREDDRAGGINGMACHINE]

lookin good

[cnote1984]

lookin good man at well trun out badass

[Twitch]

Lookin hella better dude

[rollininmy68]

glad to see someone getting to make progress on there truck..looks good

[1lowzu]

truck looks good

[Billetmaster]

Lookin good...I like it.

[12VoLt Shocker]

You have deff turned the truck into something nice, soooooooo when u planning on bd it lol jk it looks really good though

I hate you.... I should have BD it.... Now it will bug me till i do...

[chevyytruckdood]

good build i like the progress!

[12VoLt Shocker]

I wish I had something to update but my Mirrors Are MIA!..........

I Also want a BAD steering wheel but unsure of what colum adaptor to buy..?

[93stepside]

shits sick dude keep up the awsome wrk

[low_life96]

http://www.elitebillet.com/category.sc?categoryId=12
thats were i scored mine

[12VoLt Shocker]

http://www.elitebillet.com/category.sc?categoryId=12
thats were i scored mine

So I take it I would use one built for a 03 ? I know I loose the Airbab but dont the older trucks have them too? how come they just dont list the 04?

[12VoLt Shocker]

Look what I just got in for my front setup....
http://c3.ac-images.myspacecdn.com/images02/115/l_7c9b44f3c81c4000b6947fdeafcfd482.jpg
http://c4.ac-images.myspacecdn.com/images02/152/l_0f51b35896d74f2cb1701e6770708d53.jpg
Brand New QA1 12 Way adjusting shocks... Aluminum body too!...
Stole them for 250 for the pair.. Retail is 380 each...
And I blew 40 bucks on some valves...
http://c1.ac-images.myspacecdn.com/images02/119/l_133bd7cf3bc24a589f3f1cfa29a69548.jpg
There all SMC valves, I got the 4 half inch for 20 bucks, and the 2 REALLY HUGE ones for 20 bucks.. I didnt realize what I bought.. ohh well... :loser: I might need to Launch a shopping cart over a building or something..I wont be installing them on my truck thats for sure...!

I put my mirrors on my wifie bought me for Xmas! and installed a Old beater Eclipse Avn 2454 Nav unit I got for 20 bucks from some random dude..Still need a Nav disk witch will cost Allot more than 20 bucks....but enough blabbering here are Pictures..!

http://c1.ac-images.myspacecdn.com/images02/140/l_f7b0689b035c4eb88094147332128f20.jpg
http://c4.ac-images.myspacecdn.com/images02/138/l_a0be627c1a634c9fb2f83bb3c3f1162b.jpg

[shaggy1071]

Looks like you got a Pepsi sponsor in today. lol. Looks good man.

[12VoLt Shocker]

it was for size comparison .:bporn:. I actually dont even drink soda....
Its a car audio thing...

Look how GINORMOUS those valves are... Holly fuck there big...
If there was a soda can next to them on the Ebay auction I would have seen that...LOL...

[Endobo]

Nice job on your truck! Oh yeah, I need the inspiration!!!:cheers:

[z70one96]

shit if you dont want them valves let me know! they look like 1/2

[okndnx]

so how does the atwoods paint work

[12VoLt Shocker]

The paint is working Great, but my coverage sucked Ive got rust bleeding though in a few spots...and a few spots that werent covered well...

[okndnx]

ok thanks man I have been looking at it myself

[12VoLt Shocker]

So you ready to see what Ive been up to?

Here it is...
http://c3.ac-images.myspacecdn.com/images02/130/l_91fa41cd8efc401ab51ba914e1e11b42.jpg
http://c1.ac-images.myspacecdn.com/images02/143/l_5ed420e28f6249c5ab53f08b442075c8.jpg
I started Moving some stuff around.... Moved the ECM out and down..Moved the Factory batt to the Other side and added this little battery in its place custom mounted to run JUST the Compressor...
Re Mounting the Fuse block Up and over next to the battery....This whole bracket uses FACTORY mounts and bolts ...
This will clean up the engine bay quite a bit...But also creates a little issue of harness not being long enough to rout like I wanted....

Sooo this happend....
http://c4.ac-images.myspacecdn.com/images02/142/l_5a5adfb38fb4421b923d79c0a69984cb.jpg
I actually Cut that added length from another truck.. so its only going to be a single splice for the most part... it will add about 20 to 25 inches of harnes...
I am ALSO cutting the harness from the BACK of the firewall and moving it to the SIDE of the firewall to come out behind the fender under the wiper cowl...
I already moved the Cruse control module to inside the wiper cowl and extended those harnesses also...
I think it cleaned up the firewall a bit... should be REAL nice when its all done...

This is where the harness will come out of...
http://c4.ac-images.myspacecdn.com/images02/145/l_408d816641804a9f839bd3373e884fdf.jpg


Removed cruse and flipped inside cowl
http://c4.ac-images.myspacecdn.com/images02/147/l_88e154610c4a47ec95ec0161bd9ca35f.jpg


Cruse cable and brake booster harness coming from OUT of the wiper cowl... Slick right...


http://c3.ac-images.myspacecdn.com/images02/125/l_951c20036ea4415aac44366f93ad536a.jpg
http://c3.ac-images.myspacecdn.com/images02/125/l_758a0bec15c04d208d9b5e1daa2bd1ca.jpg

I also Built some Fenders... I know I said I would'nt uses any trailer fenders... But I changed my mind....LOL....
http://c4.ac-images.myspacecdn.com/images02/147/l_0d9efe0c60944cd49f2f3fcbe6b9e7f3.jpg


Super tight Fit on the outside edge... and I will lap the outer fender into the inside of the sheet from the trailer fender inner panel...

This started as a SINGLE Tandem trailer fender I cut in half...
Also using factory mounting hardware and locations....
http://c4.ac-images.myspacecdn.com/images02/149/l_86dc3c789c8448898254ae919a8afc13.jpg
http://c4.ac-images.myspacecdn.com/images02/147/l_a76b7912344c4393b1113d90e7631993.jpg

[85c10on20s]

You are amazing.. take a break from your truck and come work on mine....also give me a wesite or something where you got them mirrors from.

[12VoLt Shocker]

ebay... there Motorcycle mirrors.....

I might halfto work on your truck to dispel any bad "Ju Ju" that might come with that stolen tailgate... :D

[85c10on20s]

hahahaha true.... i really would think it'd be cool if you shaved my sidemarkers.. or and mirrors to even the price lmao!! it'd be sweet i buy the supplies like body filler and paint or whatver is needed you just do the hardwork.(its hard to me anyways)!

[12VoLt Shocker]

hahahaha true.... i really would think it'd be cool if you shaved my sidemarkers.. or and mirrors to even the price lmao!! it'd be sweet i buy the supplies like body filler and paint or whatver is needed you just do the hardwork.(its hard to me anyways)!

I would be down deff... but I actually dont have the right welder... I would halfto wait till i pick up a nice MIG welder...

[BAGD94RNGR]

The build looks great for a first time welder. Sounds like you learned alot through out this build.

[1sicluv]

i like it

[12VoLt Shocker]

hell yea so the last few days of work have been 1/2 productive.....

Going a new direction with the wire tuck/fuse box thing... But I think it will be worth it....:rolleyes:

[low_life96]

So I take it I would use one built for a 03 ? I know I loose the Airbab but dont the older trucks have them too? how come they just dont list the 04?

yea u thank they are the same but i could be wrong

[12VoLt Shocker]

http://c1.ac-images.myspacecdn.com/images02/114/l_1826e941c9254771a36fd73138d547d4.jpg
Cut and moved the wires Grommet from the fire wall to the inside under fender...

http://c2.ac-images.myspacecdn.com/images02/122/l_81d54aeb4a414b18935ae3236a0db5bd.jpg
Half the harness to the fuse block without extending already will go though...

http://c3.ac-images.myspacecdn.com/images02/140/l_adb9b14f2ff3442da3d447be6c227896.jpg
relocated interior module...

http://c1.ac-images.myspacecdn.com/images02/141/l_e1ffce5c303b4243be4eac922a22d4fc.jpg
New fuse block home... up a little though and to the left ..... little more left... a wee bit left ... yea eya you get the idea...:dontknow:
http://c3.ac-images.myspacecdn.com/images02/116/l_c083571c68df4aaeacdf328e71e95b0e.jpg
This is all that needs to be adding wire to... not bad... cut 2 holes for wire move one add one..extend 1 harness, and about 6 connectors...re arrange stuff and make room under dash... re loom it tie it down and thats it..... its fuggin simple...:cheers:

Ill post pictures of the NEW hole in the firewall as soon as i can get a hole there... stupid cheap hole saw....

[( . )( . )]

Hell yeah. Looks good. Im going the other way with mine. Im relocating the fuse box and computer behind the front bumper under the core support. Its alot more work but should be worth the look and not have a cluster behind the dash.

[dirtybird95]

truck looks sick man good work

[12VoLt Shocker]

I looked at it from both angles.. moving everything to the bumper then what i did... I think after i am all done and everything is loomed it will still be very clean even under the dash
But under the hood will be even cleaner this way since all the engine harness will be tucked too....on a V6 you gotta do something to dress it up a bit....

under bumper was actually simple and less cutting but more wiring...wich is easy...

[( . )( . )]

Yeah I'm not looking forward to extending the two huge harnesses! That's the only reason why mine doesn't run yet!

[CLEARANCE ISSUES]

Looks sick man

[DanDan]

aw skeet skeet

[12VoLt Shocker]

:cool:Yeah I'm not looking forward to extending the two huge harnesses! That's the only reason why mine doesn't run yet!

Lets work something out... I need a few things done that you might feal better about doing an i can do your wire tuck....

[DanDan]

its a bro-mance in the making :)

[12VoLt Shocker]

its a bro-mance in the making :)


LOL....... maybe a dutch rudder in the near future......:D

[DanDan]

:dito:

[12VoLt Shocker]

2:30 in da to fuckin late or whatever but I am posting up some progress...


:2girls:
Eat it up bitches!


Dunno WHY i am posting up progress here FIRST! because my last update just went un noticed... Maybe its because you are all sleeping... LOL....:rolleyes:


I scrapped the under hood relocation for a full on wire tuck to moving all the components to under the dash...except the battery and overflow and washer bottle..

I needed to extend 1 BLOCK * its Green * and 1 Harness, both these run the lighting on the front and the air bag sensors...and i had to add the fog lamp wiring pin to the block since the Donar truck was missing fog lamps...

That is what i did tonight...

This needs to be under the dash ... SO make it longer... right...

http://c3.ac-images.myspacecdn.com/images02/116/l_c083571c68df4aaeacdf328e71e95b0e.jpg

I Robbed another truck for as much of this harness i could get....
And cut the end off mine one by one and added it to the back of the donar block.. (Green)
http://c2.ac-images.myspacecdn.com/images02/119/l_e721cea39ca44e80a903a2223136acb1.jpg
LoL No going back eh.... I am not at all worried...:eyecrzy:
http://c2.ac-images.myspacecdn.com/images02/141/l_042eefda5c8249fcb93974cd8ccaf75d.jpg
I marked the Cut areas with RED tap if ever there is a issue...
Witch I dont think i will with quality work like this...
http://c4.ac-images.myspacecdn.com/images02/123/l_48f5c3eaa0fc4ca0807b027c74a411ef.jpg
I Kinda Improvised my work area.. and it turned out really good...
I would shove the harnesses barbed mounts into the cardboard and it would hold the wire perfectly still and i also used it to clean the tip...
http://c3.ac-images.myspacecdn.com/images02/119/l_5d56f5bd710442f1b829f55d5a749392.jpg
And that is the slack i have for moving it under the dash.. Should work just fine...
I passed the wire though the NEW hole in the side of the dash and the green harness though the old E brake boot in the lower floor....
http://c2.ac-images.myspacecdn.com/images02/130/l_61736551b7414c07bb7f3168c34caf39.jpg

[DanDan]

nice brotha

[WHATASIZE]

Great lookin truck man hopefully by may I will have my dime rollin again and I will catch up with ya in lawton

[12VoLt Shocker]

Filled the hole in the firewall today... I think it looks good for a first time patching with a mig in 14 years...



http://c4.ac-images.myspacecdn.com/images02/132/l_996688479a914f169992fde3618f8ce3.jpg

[DanDan]

Nice

[stantheman]

I think youve got a rat problem in that truck, you need to fix that shit! LOL

[85c10on20s]

whats the plans for the tailgate off my truck

[DanDan]

updates?

[12VoLt Shocker]

whats the plans for the tailgate off my truck

I got some plans... But its already cut up....

Sorry No updates today.. Might get back on it tonight...

I need a 3 1/2 hole saw for metal or a air saw....

[12VoLt Shocker]

http://vids.myspace.com/index.cfm?fuseaction=vids.individual&videoid=104869784

That about sums it up... It runs perfect....all the electronics work as there intended...
Just got to finish up all the loom, and paint the cut areas of the firewall... Then its on to everything else....on the front end....

http://c1.ac-images.myspacecdn.com/images02/123/l_87e1cca37dbc4200b8c09ac10913bf20.jpg
Battery mount....and new hole in side of fire wall...
http://c3.ac-images.myspacecdn.com/images02/134/l_02cc9f2299164016976d05e2a4239e8a.jpg
Ebrake cable use to run though there... Now its for the harness...
http://c4.ac-images.myspacecdn.com/images02/86/l_0e12d34c55f44941b1bf89cd6b10043f.jpg
Filled the hole in the firewall ...
http://c3.ac-images.myspacecdn.com/images02/133/l_eedc45ac53f644e9813900dca68821ae.jpg
http://c2.ac-images.myspacecdn.com/images02/104/l_3006215d2677431ba7c300ec4bc864a5.jpg
Added a hole behind the block for ECU harness...
http://c4.ac-images.myspacecdn.com/images02/85/l_bc32dc1733bc404aa5bd35b7584b56bf.jpg
http://c2.ac-images.myspacecdn.com/images02/107/l_5f3dd2a5310446ab8581750c2ce1d921.jpg
everything under the dash....

[93mazdawg]

anything else going in that hole?

[12VoLt Shocker]

anything else going in that hole?

yea Factory Grommets they are the exact same cutout as factory size firewall grommets... I still need to install those... This was just testing the extended harness

[93mazdawg]

ahh ok i see i see :) lookin good

[DanDan]

Sick

[Twitch]

looks good

[AlwaysStunting]

nice i hate wireing !!!

[12VoLt Shocker]

nice i hate wireing !!!

its not so bad... when you already do it all day long...

I took my Vacation this year to do all this work !

Guess were this is......?
http://c1.ac-images.myspacecdn.com/images02/127/l_6cc0a8b50c91412bb6eaaef7b4b247e4.jpg
Under HERE!!
http://c2.ac-images.myspacecdn.com/images02/146/l_c0f5c28101564a17a62c9228ae481e6d.jpg
yep it fits, ECU and fuse box that removes from 2 factory mounted bolts...Sweet...
http://c2.ac-images.myspacecdn.com/images02/145/l_c16540ab31d9492c9488a7dae71307d5.jpg
from the Engine though the firewall to the ECU above the fuse block ... Tight fit... for all of it.. but it clears everything.....


I actually did the wire first because I dread cutting this **** off...
http://c4.ac-images.myspacecdn.com/images02/139/l_c5de5e167b27437794b647d0ea7f5e67.jpg
yea that is .25 inch C channel steel.. and he left SOME of the factory spring perches... to hacked to use cups...
http://c3.ac-images.myspacecdn.com/images02/122/l_789495e6ee444c3ca4a7aa9b0a67cea2.jpg
http://c1.ac-images.myspacecdn.com/images02/131/l_d30e8c8ee2964a4087ca68123c7467b4.jpg
Torch cut and its a mess STILL...Notice the damage to the UCA mount where he Hacked it up with I guess a sawzaw and a crow bar....
Its ok I clean it up nice... I did leave behind some of the C channel steel and the lap welds because its simply moor metal and helps build a good foundation for my bag brackets...
Dont you think..? The welding was done well just a ****ty setup...I ground it smooth and uniform...
http://c1.ac-images.myspacecdn.com/images02/124/l_b7aee06ae52e4d55863c8be4f742d3c8.jpg

[flamethrower85]

looks good man, keep up the progress

[DanDan]

pure sex man

[12VoLt Shocker]

Im kinda stuck on how to mount my bag cups...

I want to Float them next to the frame and fill the gap between the Cup and the Frame with flat steel....

Dunno how this could work out...I just dont like the looks of flat brackets and a couple triangle gussets...

[stantheman]

It will look like crap anyway though!........J/k Damn son when you gonna quit messin with this thing. By the time your done your kids are old enough to drive and jackin ur truck!

Keep up the good work bro, cant wait to get down there and see it.

[12VoLt Shocker]

well... they are going to halfto wait...It will soon be going under the knife when they start driving......:rock:

[flamethrower85]

well y it is down just go ahead a bd it!!!!

[12VoLt Shocker]

well y it is down just go ahead a bd it!!!!

Really dont want to BD it .... I need the room for a system..... I want BIG boom..... B I G boom....

Maybe Later after I am deaf......:D

[z70one96]

body droping it wouldnt take any room up dumb dumb! lol hey man do you want some stock control arms? they came off my old 03 and there sitting in my garage in the dam way man ill give em to you. the only thing in return id like would for my alarm on the sexy truck work again... but even if you couldnt get it to work id still give them to you lmao

[stantheman]

It would if he is thinking a cut through.

[z70one96]

also i might add if you need help redoing the front ill help you man ive done the front bag plates on the same type truck befor i did josh nordeens front plates. i know what you need also

[12VoLt Shocker]

body droping it wouldnt take any room up dumb dumb! lol hey man do you want some stock control arms? they came off my old 03 and there sitting in my garage in the dam way man ill give em to you. the only thing in return id like would for my alarm on the sexy truck work again... but even if you couldnt get it to work id still give them to you lmao

YEA I actually NEED them RIGHT now... I want to try and flip the arms but dont want to waste the ball joints trying it out... and it not work...

Ill talk to austin bout checking the alarm out....

I am doing a blow though and that is why I dont want to bd it.....its gonna soak up some floor space in the bed and i need as much as i can get ... I already have a huge notch...

[z70one96]

ill drop them arms off tomorrow befor i goto work. is that cool?

[12VoLt Shocker]

Uhhh yea that is more that cool.... I would owe you one...

[12VoLt Shocker]

ill drop them arms off tomorrow befor i goto work. is that cool?

I STILL need those UCA!!!!


So this is what I am trying to figure out on then front bag cups, and shock mount...

I have some 5/16 flat steel that I want to weld first to the frame then Weld the cups to the mounts
and Build a shock tab that unbolts from the top of the cups using that stud that is on it already...
http://c4.ac-images.myspacecdn.com/images02/124/l_ee208e30ec5a46bfb333ffb5af84886b.jpg
http://c2.ac-images.myspacecdn.com/images02/141/l_e116f40a7e9e43b1a673f9bb006c84f5.jpg

My beef ass tabs...the hole in them is clearance for the bolt on the UCA to come out..

Ruff Idea of the setup and its layout, outside the truck...It will be canti outward about 10* positive angle to the frame.....

http://c1.ac-images.myspacecdn.com/images02/150/l_b524e9c100674f569da3d4c5b24b6940.jpg
http://c4.ac-images.myspacecdn.com/images02/117/l_e677315a12f743058d216b6bf92da67f.jpg
http://c4.ac-images.myspacecdn.com/images02/125/l_67c5cc3c832a44fca20cd66b33ee89db.jpg

The Only down side is that I wont be able to reach inside the tabs and weld there except where the hold is cut out maybe... BUT I want to fill the gap between frame and top of cup too... sort of box it all in .....Or is that over kill...?

http://c3.ac-images.myspacecdn.com/images02/141/l_26e040fea3b5416e84b4cb6670a82b0a.jpg

[z70one96]

I STILL need those UCA!!!!




there not uca's.... there lower control arms. iv been real busy so im droping them off tomorrow (today friday lol) around 11 on my way to work!. sorry lol :D

[DanDan]

How's it comen man

[12VoLt Shocker]

waiting on the metal shop to cut my shit.. there bullshiting me or something....

its been 2 days...


I better get them by thursday so I can get crackin.......I want this biotch on the ground and rolling again by memorial day ....

[12VoLt Shocker]

So I finished my drivers side setup...

Its ok not really how I wanted it to turn out, but I can always redo it when i body drop it....

http://c4.ac-images.myspacecdn.com/images02/144/l_4a3ae5995e354659a22014c623a676eb.jpg
Cut pieces..5/16th steel.Modded bag cup..
http://c3.ac-images.myspacecdn.com/images02/151/l_2229ad286e6c43a5a24b486585046b12.jpg
http://c3.ac-images.myspacecdn.com/images02/137/l_5f52330f5ba441cf8a91ef39a4d214e2.jpg
Modded DJM 2' Drop control arm...
http://c3.ac-images.myspacecdn.com/images02/148/l_cd8da7555ee24f24930ea5a49ef91706.jpg
http://c4.ac-images.myspacecdn.com/images02/139/l_97b11399aad14e0ca8277d92d0ddeb3f.jpg
http://c4.ac-images.myspacecdn.com/images02/137/l_34581d69ece94dc58e8a516562988c9f.jpg
Setup and test fitted...
http://c3.ac-images.myspacecdn.com/images02/145/l_381a4a7563274cc49eb89fe182d7be0a.jpg
boxed in and welded solid...

[12VoLt Shocker]

Its almost all backtogether...

Camber is TERRIBLE even with the uppers flipped, I dont get it... I need some drop spindles i guess...
Ill get pictures tonight ..

[12VoLt Shocker]

http://c2.ac-images.myspacecdn.com/images02/125/l_c808d816ce644feb84c52aaf89598d21.jpg
tight!
http://c3.ac-images.myspacecdn.com/images02/139/l_3434db6dc4cb4a35a68f040e396f570a.jpg
http://c3.ac-images.myspacecdn.com/images02/142/l_1a369ca674fb4b27aa787de62c3b9cba.jpg
Fawk Yea.... Its a dirty little whore...
http://c4.ac-images.myspacecdn.com/images02/147/l_1dc2dc44d0f74979b37a91c6838cda93.jpg
http://c4.ac-images.myspacecdn.com/images02/141/l_05f23e24dde540d98e7cc37c12ddee27.jpg
needs to get lined. up..:elephant:

[z70one96]

Its almost all backtogether...

Camber is TERRIBLE even with the uppers flipped, I dont get it... I need some drop spindles i guess...
Ill get pictures tonight ..

your most likley getting all that horrible camber from using them drop control arms.. if you add spindles it will not help you with the camber issue. all that would do is move the wheel up 2 more inches (drop it 2 inches..) Now... may i suggest you use the stock lower arms that you got form brandon, use some 2inch spindels, and knock off them bag cups... if you wanna set it up the right way then use the torsion style upper bag plates.. if you need help man CALL me ill pm you my number.. i did josh nordeens upper bag brackets.. with the setup i just decribed you will be able to lay on 22s.. and the camber the way you would go about getting little to no camber you would raise the upper control arm bracket 2 inches.. HOLLER AT ME MAN!

[12VoLt Shocker]

your most likley getting all that horrible camber from using them drop control arms.. if you add spindles it will not help you with the camber issue. all that would do is move the wheel up 2 more inches (drop it 2 inches..) Now... may i suggest you use the stock lower arms that you got form brandon, use some 2inch spindels, and knock off them bag cups... if you wanna set it up the right way then use the torsion style upper bag plates.. if you need help man CALL me ill pm you my number.. i did josh nordeens upper bag brackets.. with the setup i just decribed you will be able to lay on 22s.. and the camber the way you would go about getting little to no camber you would raise the upper control arm bracket 2 inches.. HOLLER AT ME MAN!

its all good bro... i got it under control... im just broke... ATM....Going a different route in a few months on the front and i already got balljoints installed for the front...so I am just gonna leave it alone and adjust it for the best and leave it for a bit...
i need a car to drive...:burn:

[z70one96]

its all good bro... i got it under control... im just broke... ATM....Going a different route in a few months on the front and i already got balljoints installed for the front...so I am just gonna leave it alone and adjust it for the best and leave it for a bit...
i need a car to drive...:burn:

well remeber man next time you redo the front just give me a ring and well get all that strait!

[12VoLt Shocker]

well remeber man next time you redo the front just give me a ring and well get all that strait!

Its good man I got it under control now... Its not that I know how to do it.. Its just that I followed some bad advice from Aaron Aha believe it or not, he told me that I would get the same effect with the djm arms and to ditch the spindles, I had some Beltechs and I gave em to Cory...:curse:

[DanDan]

lookn damn good bro

[12VoLt Shocker]

Ive been driving it for a day now and damn its got some bad Pull in the steering and it needs toe fixed, but feels good even without the shocks in yet...

I did get stuck in traffic today in the middle of a 3 lane road uphill too...
I Turned on my A/C, hit the gas and NOTHING... NO power I just died......
Blocking the road....

Lucky after traffic cleared I let it roll backwards downhill into a gas station Driveway ... Witch was uphill so i didnt quite make it into the lot.... LOL....

Turned out to be a fuse on the relocated under hood block... It Was the main feed fuse and a 30 amp so i put in a 50 and got a extra... been fine since...



Ohh and it was easy to change even after the relocation job...

[teckn9ne]

Pretty sure drop spindles will take out some camber! But like z70one said most people ive seen raise the uppers, looking good so far keep it up!

[12VoLt Shocker]

went out and got some better pictures of all the shit I did...

http://c1.ac-images.myspacecdn.com/images02/124/l_43432ecf8ebe4885905ca9f14b8c7ed0.jpg
Engine bay all cleaned up....looks good without that fuse block there...


Donk Lift...full lock up...
http://c4.ac-images.myspacecdn.com/images02/114/l_64c76b5cfb2448a19b0e74043914f137.jpg


I should'nt halfto explain this one to you fuckers...
http://c4.ac-images.myspacecdn.com/images02/143/l_10bd2ebd5e3848cc895bd099fcc6d3eb.jpg
http://c2.ac-images.myspacecdn.com/images02/136/l_630d812dc22546788690e8c8be694441.jpg
http://c2.ac-images.myspacecdn.com/images02/149/l_62c0bbba5f374cb887f9851845390a01.jpg

[d21cruisa]

lookin good man!!!

[00s10]

Love it man

[teckn9ne]

Lays hard and gets mega lift! Now body drop it :)

[12VoLt Shocker]

just dropped 75 bucks for fittings today... I will build a gauge cluster today at work.....

since its slow as shit...i am just gonna do it different later.. but i will be selling this one when i am done.... so lemmie know if anyone wants some Easy street gauges and a custom pod...


thanks guys... it will be body dropped when the Ls1 motor is in.....figured that would be the best time to tear into it again... I got to Get a DD first b4 i tear it a new asshole again...

[stantheman]

Truck looks great bro, its come a long way since when I first seen it.

[hardhitta71194]

Lookin damn good man. Love those rims.

[12VoLt Shocker]

Alright Things are really moving along now... taking it to hibdons to line up the front in the morning...

Tires are on and balanced, Rebuilt my air setup and moved valves and rewired to the back ran gauges for the front...
http://c2.ac-images.myspacecdn.com/images02/98/l_7136eb92f60945779529689e2f88c995.jpg
http://c1.ac-images.myspacecdn.com/images02/89/l_7e2a5e00fd1d4c7ca50a707858997d6c.jpg
http://c1.ac-images.myspacecdn.com/images02/108/l_ea74052349384e52938b8326f3b08d4c.jpg
Took some pictures of my truck at work...

http://c3.ac-images.myspacecdn.com/images02/110/l_a18ce3c231324a5ab3fe7dbe6e9346c2.jpg

[05colorado]

Sweet man looks really good i like

[z70one96]

http://c3.ac-images.myspacecdn.com/images02/110/l_a18ce3c231324a5ab3fe7dbe6e9346c2.jpg

should have had me bring the bagged truck up there. it has Treo beats in it!

[12VoLt Shocker]

I posted up a thread about the event and handed out flyers....

[DanDan]

impresive man

[stantheman]

Now prime it and make it all match in color!

[DanDan]

paint it hulk purple

[12VoLt Shocker]

It went a Round Trip on a family vacation 500 miles and odomiter just broke the 20's on the way home....

Lawton to Ada, Ada To Lake Tenkiller, And then home.....

I finally got to take the Picture Of my truck at the Loading dock at Tenkiller...Love it....
http://c3.ac-images.myspacecdn.com/images02/69/l_f9c7a1c6c1b145839bccff5e1d4992d2.jpg
http://c1.ac-images.myspacecdn.com/images02/76/l_5ec3b30ceb134c2b959487cc2e7817c0.jpg
http://c4.ac-images.myspacecdn.com/images02/62/l_84e0e7defac5410692d039ea8f4d2763.jpg

And If Someone could make me a Sig from one of these for the forums..it would be badass...

[85c10on20s]

wheres my tailgate? the idea? what is it?

[klassic_krew]

this makes me wanna bag mine! lol looks nice as hell man

[showready]

hey i got the dog dish on tool box alll i use it for is a bolt dish its yours if you want it

[12VoLt Shocker]

wheres my tailgate? the idea? what is it?

Its chopped up so its gone....
But I really dont want to say im doing with it yet.. Ive got a few cards up my ass, and dont really want to yank them out ATM ....

[12VoLt Shocker]

hey i got the dog dish on tool box alll i use it for is a bolt dish its yours if you want it

Not sure what that is, if your talking about a magnet try ive got a few, but if your talking about hub caps for chevy... then hell yea... i want to redo the box with a 9 switch one...

[showready]

yeah i got the dog dish hub cap you said you wanted to switch to so hit me up when you are around okc

[JasonHall]

That truck has come along ways.. looks good

[12VoLt Shocker]

Thanks jason....

Know if I only knew someone that could slang some paint......;)

[JasonHall]

I cant paint..Do some bodywork but no paint..

[stantheman]

I could "slang" it!

[DanDan]

updates jew